perm filename DETAIL.VL[1,VDS]2 blob sn#227058
filedate 1976-07-20 generic text, type C, neo UTF8
COMMENT ⊗ VALID 00003 PAGES
C REC PAGE DESCRIPTION
C00002 00002 \|\\M1BDR30\M2SIGN57\M3NGR25\M4NGR20\F2\CVICARM
C00007 00003 \F2\CVICARM
\F3\C154 EAST DANA STREET
\CMOUNTAIN VIEW, CA. 94041
\F1\CMANIPULATOR COMPONENT DETAILS
\J An electric manipulator with 6 degrees of freedom plus a
two fingered hand. Potentiometer, encoder or resolver position sensors and
tachometers on all axes. D.C. motor drive, with electromagnetic brakes on all joints.
Completely wired with two multiple contact connectors.
This arm has a 4.5 kg. direct lift capability.\.
\J A small 6 degree of freedom electric arm featuring six revolute joints,
d.c. motor drives and potentiometer feedback on all joints including
the hand. Tachometer feedback is
provided on 5 joints. This arm has a 1.4 kg. lift capability.\.
POWER AMPLIFIERS AND MANUAL CONTROL
\J Bipolar 35 vdc. supply, power amplifiers for all joints and hand,
remote enable logic, current limit and motor temperature sense
electronics. Brake drivers, and function select
logic. Manual control unit with computer-manual mode select switch,
emergency stop button, and brake control switches. Allows remote manual
positioning of arm without use of computer.\.
\J Hardware servo electronics for all joints and hand. Computer
selected position, velocity or torque (current) servo modes on a joint
by joint basis. Position sensor and tachometer buffer amplifiers.
Servo accuracy indicator bits. Electrical limit stops for all joints.
Servo cards plug into power amplifier unit.\.
\J Complete interface to PDP-11, Nova, or Interdata computers. Includes
power supply, all cables, and interface card for selected computer.
Interface features 12 bit A/D for 32 channels of analog signal input
(one arm plus many spares), eight 12 bit DAC
channels for arm plus one or more accessory devices. Output of brake
bits, spare command bits, servo mode select bits, and enable bits is included.
Provision for reading joint tolerance bits, touch sensor bits, and
accessory device bits.
Also provided is
emergency stop logic, and provision for orderly shutdown of arm in
case of computer failure.\.
\J Our software package is continuously being expanded.
We currently offer a special arm program editor for quickly writing
programs in our easy to use VAL language. Vicarm software includes
routines for point to
point trajectories, straight line motion in any direction, pick and place motions,
and controlled grasp motions. Precision points can be entered by typing in
coordinates (an arm solution routine is included in the software),
or by placing the arm at a desired point (Unimate mode).
Transforms are labeled and can be called at random by the program. Looping and branching
features are included.\.
\F1\CMANIPULATOR COMPONENT DETAILS
\J The Digital Equipment Corporation LSI-11 computer is used in our complete
system. This 16 bit processor with floating point processing capability has 12k words of MOS memory and
a serial data interface to a teletype terminal (supplied).
The processor, memory and interfaces are supplied with their own
power supply and operating panel. The computer is a general purpose device, and
may also be used to run other programs or operate devices other than the arm.\.
\J The complete system includes everything mentioned above packaged into
three units- the arm and hand, the power supply and servo unit, and the computer and
interface unit. All are connected by plug-in cables. Power required is
120/240 VAC. Each unit is light enough to be hand carried by one person.\.
WRIST FORCE SENSOR
\J This is a 6-component wrist mounted force balance. It uses semiconductor
strain gauges, and has internal electronics. It interfaces through the computer
interface, or can be used separately. A calibration matrix is provided.
Overload protection for all components of force and moment is included.
Force resolution is
5 grams with a range of +- 4.5 kg. Moment resolution is 15 gm-cm with a range
of +- 12 kg-cm.
This device is currently offered only for the Stanford Arm.\.
FORCE SENSING FINGERS
\J These are fingers with strain gauges mounted. They are sensitive to touching and
gripping forces. Resolution is 3 grams with a maximum force of 5 kg. Amplifiers and
signal conditioning electronics is included. This unit connects to the spare analog inputs of our
interface. Available only on the Stanford Arm.\.
TOUCH SENSING FINGERS
\J These are fingers with sensitive switches mounted in the center of the
finger pads. Their switch output can be read through the extra bit input
lines on our interface. All wires and connectors are provided. Currently
available only with the Stanford Arm.\.